Q1. An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?

A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.

B. Adjust the EtherChannel load-balancing method based on destination IP addresses.

C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.

D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.

E. Adjust the EtherChannel load-balancing method based on source IP addresses.

Q2. In which portion of the frame is the 802.1q header found?

A. within the Ethernet header

B. within the Ethernet payload

C. within the Ethernet FCS

D. within the Ethernet source MAC address

Q3. Refer to the exhibit.

f1/0 and f1/1 have the same end-to-end path cost to the designated bridge. Which action is needed to modify the Layer 2 spanning-tree network so that traffic for PC1 VLAN from switch SW3 uses switchport f1/1 as a primary port?

A. Modify the spanning-tree port-priority on SW1 f1/1 to 0 and f1/0 to 16.

B. Modify the spanning-tree port-priority on SW1 f1/1 to 16 and f1/0 to 0.

C. Modify the spanning-tree port-priority on SW2 f1/1 to 0 and f1/0 to 16.

D. Modify the spanning-tree port-priority on SW2 f1/1 to 16 and f1/0 to 0.

Q4. Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.

What is the virtual mac-address of HSRP group 1?

A. 0000.0c07.ac02

B. 4000.0000.0010

C. 0000.0c07.ac01

D. 4000.0000.ac01

E. 4000.0000.ac02

F. 0000.0c07.0010

Q5. Which statement is correct about 802.1Q trunking?

A. Both switches must be in the same VTP domain.

B. The encapsulation type of both ends of the trunk does not have to match.

C. The native VLAN on both ends of the trunk must be VLAN 1.

D. 802.1Q trunking can only be configured on a Layer 2 port.

E. In 802.1Q trunking, all VLAN packets are tagged on the trunk link, except the native VLAN.

Q6. Which will identify the master switch in stack wise?

A. lower priority

B. higher priority

C. lower id

D. higher id

Q7. When you configure a private VLAN, which type of port must you configure the gateway router port as?

A. promiscuous port

B. isolated port

C. community port

D. access port

Q8. A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to spike during peak working hours. What is the root cause of this issue?

A. The VLAN receives additional frames from neighboring switches.

B. The SDM VLAN template causes the MAC address-table to overflow.

C. The VLAN template disables routing in hardware.

D. The switch needs to be rebooted before the SDM template takes effect.

Q9. Which type of information does the DHCP snooping binding database contain?

A. untrusted hosts with leased IP addresses

B. trusted hosts with leased IP addresses

C. untrusted hosts with available IP addresses

D. trusted hosts with available IP addresses

Q10. What is the maximum number of switches that can be stacked using Cisco StackWise?

A. 4

B. 5

C. 8

D. 9

E. 10

F. 13

Q11. Which authentication service is needed to configure 802.1x?

A. RADIUS with EAP Extension

B. TACACS+

C. RADIUS with CoA

D. RADIUS using VSA