200-125 Exam Questions - Online Test
200-125 Premium VCE File
150 Lectures, 20 Hours
Want to know Ucertify ccna routing and switching 200 125 official cert guide library Exam practice test features? Want to lear more about Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certification experience? Study Virtual Cisco ccna 200 125 syllabus answers to Update ccna 200 125 questions at Ucertify. Gat a success with an absolute guarantee to pass Cisco 200 125 ccna (CCNA Cisco Certified Network Associate CCNA (v3.0)) test on your first attempt.
P.S. Virtual 200-125 item pool are available on Google Drive, GET MORE: https://drive.google.com/open?id=1G0OQvn58oVaFHU8QUjdLariF4zPSu0BB
New Cisco 200-125 Exam Dumps Collection (Question 10 - Question 19)
New Questions 10
Refer to the exhibit.
Which of these statements correctly describes the state of the switch once the boot process has been completed?
A. As FastEthernet0/12 will be the last to come up, it will be blocked by STP.
B. Remote access management of this switch will not be possible without configuration change.
C. More VLANs will need to be created for this switch.
D. The switch will need a different IOS code in order to support VLANs and STP.
Answer: B
Explanation:
Notice the line, which says u201cInterface VLAN1, changed state to administratively downu201d. This shows that VLAN1 is shut down. Hence remote management of this switch is not possible unless VLAN1 is brought back up. Since VLAN1 is the only interface shown in the output, you have to assume that no other VLAN interface has been configured with an IP Address.
New Questions 11
A network administrator is troubleshooting an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?
A. Router# show ip eigrp adjacency
B. Router# show ip eigrp topology
C. Router# show ip eigrp interfaces
D. Router# show ip eigrp neighbors
Answer: D
Explanation:
Below is an example of the show ip eigrp neighbors command. The retransmit interval (Smooth Round Trip Timer u2013 SRTT) and the queue counts (Q count, which shows the number of queued EIGRP packets) for the adjacent routers are listed:
New Questions 12
What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?
A. 2
B. 8
C. 16
D. unlimited
Answer: B
Explanation:
maximum-paths (OSPF)
To control the maximum number of parallel routes that Open Shortest Path First (OSPF) can support, use themaximum-pathscommand.
Syntax Description
maximum
Maximum number of parallel routes that OSPF can install in a routing table. The range is from 1 to 16 routes.
Command Default
8paths
New Questions 13
Refer to the exhibit.
Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.
Answer: D,F
Explanation:
In order for multiple VLANs to connect to a single physical interface on a Cisco router, subinterfaces must be used, one for each VLAN. This is known as the router on a stick configuration. Also, for any trunk to be formed, both ends of the trunk must agree on the encapsulation type, so each one must be configured for 802.1q or ISL.
New Questions 14
Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link?
A. show frame-relay lmi
B. show frame-relay map
C. show frame-relay pvc
D. show interfaces serial
Answer: B
Explanation:
When connecting Cisco devices with non-Cisco devices, you must use IETF4 encapsulation on both devices. Check the encapsulation type on the Cisco device with the show frame-relay mapexec command.
New Questions 15
What is a global command?
A. a command that is set once and affects the entire router
B. a command that is implemented in all foreign and domestic IOS versions
C. a command that is universal in application and supports all protocols
D. a command that is available in every release of IOS, regardless of the version or deployment status
E. a command that can be entered in any configuration mode
Answer: A
Explanation:
When you enter global configuration mode and enter a command, it is applied to the running configuration file that is currently running in ram. The configuration of a global command affects the entire router. An example of a global command is one used for the hostname of the router.
New Questions 16
Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information? (Choose two.)
A. the amount of available ROM
B. the amount of available flash and RAM memory
C. the version of the bootstrap software present on the router
D. show version
E. show processes
F. show running-config
Answer: B,D
Explanation:
When upgrading a new version of the IOS we need to copy the IOS to the Flash so first we have to check if the Flash has enough memory or not. Also running the new IOS may require more RAM than the older one so we should check the available RAM too. We can check both with the u201cshow versionu201d command.
New Questions 17
Refer to the exhibit.
Which statement is true?
A. The Fa0/11 role confirms that SwitchA is the root bridge for VLAN 20.
B. VLAN 20 is running the Per VLAN Spanning Tree Protocol.
C. The MAC address of the root bridge is 0017.596d.1580.
D. SwitchA is not the root bridge, because not all of the interface roles are designated.
Answer: D
Explanation:
Only non-root bridge can have root port. Fa0/11 is the root port so we can confirm this
switch is not the root bridge ->.
From the output we learn this switch is running Rapid STP, not PVST ->. 0017.596d.1580 is the MAC address of this switch, not of the root bridge. The MAC address of the root bridge is 0017.596d.2a00 ->.
All of the interface roles of the root bridge are designated. SwitchA has one Root port and 1 Alternative port so it is not the root bridge.
New Questions 18
A network administrator is trying to add a new router into an established OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers. Given the information in the partial configuration shown below, what configuration error is causing this problem?
Router(config)# router ospf 1
Router(config-router)# network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly.
B. The OSPF area is configured improperly.
C. The network wildcard mask is configured improperly.
D. The network number is configured improperly.
E. The AS is configured improperly.
F. The network subnet mask is configured improperly.
Answer: C
Explanation:
When configuring OSPF, the mask used for the network statement is a wildcard mask similar to an access list. In this specific example, the correct syntax would have been u201cnetwork 10.0.0.0 0.0.0.255 area 0.u201d
New Questions 19
Which statement is correct regarding the operation of DHCP?
A. A DHCP client uses a ping to detect address conflicts.
B. A DHCP server uses a gratuitous ARP to detect DHCP clients.
C. A DHCP client uses a gratuitous ARP to detect a DHCP server.
D. If an address conflict is detected, the address is removed from the pool and an administrator must resolve the conflict.
E. If an address conflict is detected, the address is removed from the pool for an amount of time configurable by the administrator.
F. If an address conflict is detected, the address is removed from the pool and will not be reused until the server is rebooted.
Answer: D
Explanation:
An address conflict occurs when two hosts use the same IP address. During address assignment, DHCP checks for conflicts using ping and gratuitous ARP. If a conflict is detected, the address is removed from the pool. The address will not be assigned until the administrator resolves the conflict.
(Reference: http://www.cisco.com/en/US/docs/ios/12_1/iproute/configuration/guide/1cddhcp.html)
100% Update Cisco 200-125 Questions & Answers shared by Dumpscollection, Get HERE: http://www.dumpscollection.net/dumps/200-125/ (New 573 Q&As)
- All About Breathing 200-125 practice test
- High value 300-165 Dumps Questions 2021
- The Rebirth Guide To 210-260 examcollection
- Downloadable CCNA Security 210-260 examcollection
- The Secret of Cisco 300-206 vce
- A Review Of Free 300-115 exam
- Improve 500-901 Test Questions For Cisco Data Center Unified Computing Infrastructure Design Certification
- Cisco 200-155 Questions 2021
- What Refined 100-105 examcollection Is?
- Down to date Cisco 200-125 exam question