300-115 Exam Questions - Online Test

300-115 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

Top Quality of cisco 300 115 exam price materials and free samples for Cisco certification for candidates, Real Success Guaranteed with Updated ccnp switch 300 115 dumps pdf pdf dumps vce Materials. 100% PASS SWITCH Implementing Cisco IP Switched Networks exam Today!

P.S. Top Quality 300-115 free samples are available on Google Drive, GET MORE: https://drive.google.com/open?id=1CfKI5pbjCPmPD71IOn4nWDyRdJ9zMspQ

New Cisco 300-115 Exam Dumps Collection (Question 4 - Question 13)

Question No: 4

Which statement describes the result of configuring SPAN on a Cisco device?

A. If not carefully planned, SPAN can lead to loops between source and destination ports.

B. SPAN doubles traffic internally

C. SPAN blocks for normal use one additional port for each configured source port

D. SPAN halves the capacity of the source port.

Answer: A

Question No: 5

In which state does the standby virtual gateway take election?

A. learn

B. listen

C. init

D. reply

Answer: B

Question No: 6

Refer to the exhibit.

An engineer is configuring EtherChannel between two switches and notices the console message on switch 2. Based on the output, which option describes the reason for this error?

A. Switch 1 does not have enough member ports configured.

B. Switch 2 has too many member ports configured.

C. The port channel interface numbers do not match.

D. The EtherChannel protocols do not match.

Answer: D

Question No: 7

In a switch stack environment, what is the total bidirectional traffic flow between two logical counter-rotating paths?

A. 16 Gbps

B. 32 Gbps

C. 64 Gbps

D. 128 Gbps

Answer: B

Question No: 8

Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?

A. They have been configured with the spanning-tree bpdufilter disable command.

B. They have been configured with the spanning-tree bpdufilter enable command.

C. They have been configured with the spanning-tree bpduguard disable command.

D. They have been configured with the spanning-tree bpduguard enable command.

E. They have been configured with the spanning-tree guard loop command.

F. They have been configured with the spanning-tree guard root command.

Answer: F

Question No: 9

Which keyword can be applied to the spanning-tree priority command that allows the IT department to adjust the timers based on the number of switches between any two end stations?

A. hello-time

B. cost

C. diameter

D. priority

E. root primary

Answer: C

Explanation: Use the diameter keyword to specify the Layer 2 network diameter (that is, the maximum number of switch hops between any two end stations in the Layer 2 network). When you specify the network diameter, the switch automatically sets an optimal hello time, forward-delay time, and maximum-age time for a network of that diameter,

which can significantly reduce the convergence time. You can use the hello keyword to override the automatically calculated hello time.

Question No: 10

It a switch stack is configured to used SDM templates, where are the templates stored?

A. stack master

B. TFTP server

C. flash memory

D. all stack members

Answer: A

Question No: 11

When a Cisco Catalyst switch that is configured in VTP server mode is first booted, which two VLAN ranges are loaded on the switch?

A. all VLAN are in the VLAN database.

B. VLANs greater than 1005 in the startup-config file

C. the first 1005 VLANs in the VLAN database file

D. the first 1005 VLANs in the startup-config file

E. VLANs greater than 1005 in the VLAN database file

Answer: B,D

Question No: 12

Which feature prevents from sending BPDUs on a portfast enabled port?

A. BPDU guard

B. PortFast

C. root guard

D. BPDU filtering

Answer: D

Question No: 13

Refer to the exhibit.

You change a switch SDM template to maximize the number of supported MAC addresses You notice that the switch routing performance has been significantly degraded. Which action do you take to correct the problem?

A. Configure the sdm prefer routing command

B. Execute the clear ip route * command to reset the routing table.

C. Configure the sdm prefer default command

D. Configure the sdm prefer vlan command.

Answer: C

P.S. Easily pass 300-115 Exam with Allfreedumps Top Quality Dumps & pdf vce, Try Free: https://www.allfreedumps.com/300-115-dumps.html (416 New Questions)