300-115 Exam Questions - Online Test

300-115 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

Master the 9tut ccnp switch 300 115 Implementing Cisco IP Switched Networks content and be ready for exam day success quickly with this Actualtests ccnp switch 300 115 free question. We guarantee it!We make it a reality and give you real cbt nuggets ccnp switch 300 115 download questions in our Cisco certprepare 300 115 braindumps.Latest 100% VALID Cisco ccnp switch 300 115 Exam Questions Dumps at below page. You can use our Cisco 300 115 dumps braindumps and pass your exam.

Q41. Refer to the exhibit.

What is the result of the configuration?

A. The EtherChannels would not form because the load-balancing method must match on the devices.

B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.

C. The EtherChannels would form, but network loops would occur because the load- balancing methods do not match.

D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.

Answer: B

Q42. Which VLAN range is eligible to be pruned when a network engineer enables VTP pruning on a switch?

A. VLANs 1-1001

B. VLANs 1-4094

C. VLANs 2-1001

D. VLANs 2-4094

Answer: C

Q43. Which command creates a login authentication method named "login" that will primarily use RADIUS and fail over to the local user database?

A. (config)# aaa authentication login default radius local

B. (config)# aaa authentication login login radius local

C. (config)# aaa authentication login default local radius

D. (config)# aaa authentication login radius local

Answer: B

Q44. Refer to the exhibit.

Which set of configurations will result in all ports on both switches successfully bundling into an EtherChannel?

A. switch1

channel-group 1 mode active switch2

channel-group 1 mode auto

B. switch1

channel-group 1 mode desirable switch2

channel-group 1 mode passive

C. switch1

channel-group 1 mode on switch2

channel-group 1 mode auto

D. switch1

channel-group 1 mode desirable switch2

channel-group 1 mode auto

Answer: D

Q45. Which command is needed to enable DHCP snooping if a switchport is connected to a DHCP server?

A. ip dhcp snooping trust

B. ip dhcp snooping

C. ip dhcp trust

D. ip dhcp snooping information

Answer: A

Q46. RSPAN has been configured on a Cisco Catalyst switch; however, traffic is not being replicated to the remote switch. Which type of misconfiguration is a cause?

A. The RSPAN designated VLAN is missing the remote span command.

B. The local and remote RSPAN switches are configured using different session IDs.

C. The local RSPAN switch is replicating only Rx traffic to the remote switch.

D. The local switch is overloaded with the amount of sourced traffic that must be replicated to the remote switch.

Answer: A

Q47. What is the function of NSF?

A. forward traffic simultaneously using both supervisors

B. forward traffic based on Cisco Express Forwarding

C. provide automatic failover to back up supervisor in VSS mode

D. provide nonstop forwarding in the event of failure of one of the member supervisors

Answer: D

Q48. Refer to the exhibit.

When troubleshooting a network problem, a network analyzer is connected to Port f0/1 of a LAN switch. Which command can prevent BPDU transmission on this port?

A. spanning-tree portfast bpduguard enable

B. spanning-tree bpduguard default

C. spanning-tree portfast bpdufilter default

D. no spanning-tree link-type shared

Answer: C

Q49. When you configure a private VLAN, which type of port must you configure the gateway router port as?

A. promiscuous port

B. isolated port

C. community port

D. access port

Answer: A

Q50. A network engineer configured a fault-tolerance link on Gigabit Ethernet links G0/1, G0/2, G0/3, and G0/4 between two switches using Ethernet port-channel. Which action allows interface G0/1 to always actively forward traffic in the port-channel?

A. Configure G0/1 as half duplex and G0/2 as full duplex.

B. Configure LACP port-priority on G0/1 to 1.

C. Configure LACP port-priority on G0/1 to 65535.

D. LACP traffic goes through G0/4 because it is the highest interface ID.

Answer: B