NEW QUESTION 1

Exhibit.

A customer is testing a dual-fabric FC SAN configuration as shown in the exhibit. The zones are implemented on the switches shown below.

IF all the nodes are in the SLM reporting nodes list, how many paths per LUN should the customer expect when simulating a node failure by powering off Node 04?

• A. 4 paths
• B. 6 paths
• C. 8 paths
• D. 2 paths

Answer: B

NEW QUESTION 2

Which commands allow you to enable NetApp deduplication and verify space savings?

• A. sis on <vol>, sis start <vol>, df s <vol>
• B. asis on <vol>, asis start <vol>, df s <vol>
• C. sis on <vol>, sis start <vol>, df r <vol>
• D. sis on, sis start, df p <vol>

Answer: A

NEW QUESTION 3

Exhibit.

You are working on a project to install a new AFF A300 storage array. You use a pair of Nexus 3596 switches for FC connectivity between your VMware ESXi servers and the AFF A300.
Which SAN switch feature must be enabled to accomplish this task?

• A. N_Port ID visualization (NP1V)
• B. Open Shortest Path First (OSPF)
• C. Link Aggregation Control Protocol (LACP)
• D. N_Port Visualization (NPV)

Answer: A

NEW QUESTION 4

An administrator is configuring their existing Ethernet network switches to provide ISCSI LUNs to several servers. The network switches are also used for other traffic from various hosts. In this scenario,
which statement is true?

• A. Increase the ratio of access ports to trunk ports to 2:1
• B. Configure the MTU size to be larger on the switch and storage than on the host.
• C. Use multiple VLANs to isolate traffic from other network traffic
• D. Netapp recommends using the same LIFs for NFS and ISCSI traffic

Answer: C

Explanation:
VLANs offer specific benefits, such as increased security and improved network reliability that you might want to leverage in iSCSI.
You can find more information on this link:
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sanconf/SAN%20configuration.pdf (page 5)

NEW QUESTION 5

You want to ensure maximum performance of iSCSI LUNs on an AFF A220. In this scenario, which two actions will accomplish this task? (Choose two.)

• A. Disable flow control.
• B. Configure virtual LAN (VLAN).
• C. Enable flow control.
• D. Enable jumbo frames.

Answer: CD

NEW QUESTION 6

You deployed a new SVM for FC access, and you used the vserver fcr, create -vserver svm1 - status-admin up command to enable FC service on the SVM. You then created the LIFs for the FC protocol. When you review the status of the LIFs, they show that the admin status is up, but the operational status is down. You have already verified that the ports are physically connected.
In this scenario, what is the next step to bring the LIFs up?

• A. Use the network interface modify command to change the operational status of the LIFs.
• B. Create at least one zone that contains your SVM LIF WWPNs and an initiator.
• C. Verify that an FC license is applied on your system.
• D. Disable the SAN switch port where your NetApp storage is connected.

Answer: B

NEW QUESTION 7

An administrator enabled the FCP protocol on an SVM and created a boot LUN for a Windows Server 2019 server host. The host is attached using multiple paths to the storage SVM. After correctly adding
the LUN to the igroup and setting its LUN ID to 1, the host is unable to boot using the installed FC HBA.

• A. The LUN ID must be set to 0
• B. The LUN ID must be set to 255
• C. During the boot process, using FCP is not supported by Netapp
• D. During the boot process, using FCP is not supported by Microsoft

Answer: A

Explanation:
Create the LUN that you want to use as a boot device, and map it to the igroup as LUN ID 0 You can find more information on this link:
https://library.netapp.com/ecmdocs/ECMP1656701/html/GUID-76BFD6AC-BC2A-419A-9DD3-D98423B2B6

NEW QUESTION 8

Which type of multipathing does Linux support?

• A. dm_mp
• B. dsm
• C. mpio
• D. mcs

Answer: A

NEW QUESTION 9

You have a SAN host that is only sending traffic to an ONTAP cluster using active non-optimized paths. In this scenario, over which network type does the node that is hosting the target LUN receive the
traffic?

• A. Fibre Channel network
• B. Cluster network
• C. ISCSI network
• D. Intercluster network

Answer: B

Explanation:
The Cluster Network
This is used for traffic that is going between the nodes themselves, such as system information that is being replicated between the nodes. Also, if incoming client data traffic hits a network port on a different
controller than the one which owns the disks, that traffic will also go over the cluster network.

NEW QUESTION 10

You will be purchasing two high availability NetApp AFF A700s systems. You want to set up a 4-node cluster. Which switch would you use for the cluster interconnect switches?

• A. NetApp CN1610
• B. Cisco Nexus 3132Q-V
• C. Cisco Nexus 5548UP
• D. Cisco Nexus 5020

Answer: B

NEW QUESTION 11

You create a new iSCSI SVM and secure iSCSI sessions by using both Challenge-Handshake Authentication Protocol (CHAP) and iSCSI Access Control Lists (ACL).
In this scenario, in which two ways are you securing your iSCSI implementation? (Choose two.)

• A. CHAP creates a hash value for the username and shared secret.
• B. iSCSI ACLs are applied to the initiator configuration to provide an IP address of the targets.
• C. CHAP encrypts all iSCSI session I/O.
• D. iSCSI ACLs are applied to the target configuration to provide an IP address of the initiators.

Answer: AD

NEW QUESTION 12


You have an existing 2-node AFF A300 cluster with premium bundle licensing applied. You need to have consistently low front end latency, and have determined that NVMe satisfies this requirement.
Referring to the exhibit, which two actions would accomplish this task? (Choose two.)

• A. Add a UTA2 adapter to each of the two AFF A300 nodes.
• B. Add a 32 GB FC HBA to each of the two AFF A300 nodes.
• C. Apply the license for FCP.
• D. Apply the license for NVMe.

Answer: B

NEW QUESTION 13

A customer has multiple host applications that require FC block storage. You need to gather and validate the customer’s requirements for a supported NetApp solution.
Which two tools would be used to accomplish this task? (Choose two.)

• A. Interoperability Matrix Tool (IMT)
• B. OneCollect
• C. Config Advisor
• D. Hardware Universe (HWU)

Answer: AD

Explanation:
Reference: https://www.netapp.com/us/technology/interop.aspx

NEW QUESTION 14

A company wants to use jumbo frames in their Ethernet network. They should set the packet size to which industry conventional value?

• A. 1200
• B. 1500
• C. 9000
• D. 12000

Answer: C

NEW QUESTION 15

Your customer asks you how to connect a host for SAN access to the newly installed AFF A400 system. In this scenario, which two statements are correct? (choose two)

• A. Direct Connection to the nodes from the hosts with ISCSI is supported
• B. Direct Connection to the nodes from the hosts with ISCSI is not supported
• C. Direct Connection to the nodes from the hosts with FC is not supported
• D. Direct Connection to the nodes from the hosts with FC is supported

Answer: AC

Explanation:
ISCSI-Direct-attachment: In a direct-attached configuration, one or more hosts are directly connected to the controllers.
You cannot directly attach FC or FC-NMVE SAN hosts to single nodes without using an FC switch. You can find more information on this link:
https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-sanconf%2FGUID-193CC377-5C

NEW QUESTION 16
......