100-105 Exam Questions - Online Test

100-105 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

we provide Approved Cisco ccent 100 105 pdf testing engine which are the best for clearing 105 100 test, and to get certified by Cisco ICND1 Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0). The 100 105 exam Questions & Answers covers all the knowledge points of the real icnd 100 105 exam. Crack your Cisco ccent 100 105 pdf Exam with latest dumps, guaranteed!

P.S. Approved 100-105 faq are available on Google Drive, GET MORE: https://drive.google.com/open?id=1bsb-sFsEjKH4qxNCkR_EoI2fGRgBevmQ

New Cisco 100-105 Exam Dumps Collection (Question 6 - Question 15)

New Questions 6

What is the requirement of configuring 6to4 tunnelling on two routers?

A. Both ipv6 and ipv4 must be configured

B. Only IPv6

C. Only IPv4

Answer: A

New Questions 7

An administrator issues the show ip interface s0/0 command and the output displays that interface Serial0/0 is up, line protocol is up What does "line protocol is up" specifically indicate about the interface?

A. The cable is attached properly.

B. CDP has discovered the connected device.

C. Keepalives are being received on the interface.

D. A carrier detect signal has been received from the connected device.

E. IP is correctly configured on the interface.

Answer: C

New Questions 8

Which port-security feature allows a switch to learn MAC addresses dynamically and add them to the running configuration?

A. security violation restrict mode

B. switch port protection

C. sticky learning

D. security violation protect mode

Answer: C

Explanation:

You can configure an interface to convert the dynamic MAC addresses tosticky secure MAC addresses and to add them to the running configuration by enabling sticky learning. To enable sticky learning, enter the switchport port-security mac-address sticky interface configuration command. When you enter this command, the interface converts all the dynamic secure MAC addresses, including those that were dynamically learned before sticky learning was enabled, to sticky secure MAC addresses.

New Questions 9

Refer to the exhibit.

All devices attached to the network are shown. Which number of collision domains are

present in this network?

A. 9

B. 3

C. 6

D. 2

E. 15

Answer: E

Explanation: Both switch and router separate collision domains. In other words, each port of the switch and router creates one collision domain so we have 15 collision domains in this topology.

New Questions 10

Which statement about routing protocols is true?

A. Link-state routing protocols choose a path by the number of hops to the destination.

B. OSPF is a link-state routing protocol.

C. Distance-vector routing protocols use the Shortest Path First algorithm.

D. IS-IS is a distance-vector routing protocol.

Answer: B

New Questions 11

Refer to the output of the three router commands shown in the exhibit.

A new technician has been told to add a new LAN to the company router. Why has the technician received the error message that is shown following the last command?

A. The interface was already configured.

B. The interface type does not exist on this router platform.

C. The IOS software loaded on the router is outdated.

D. The router does not support LAN interfaces that use Ethernet.

E. The command was entered from the wrong prompt.

Answer: B

Explanation:

From the output of the u201cshow versionu201d command, we learn that there are only 2 FastEthernet interfaces (2 FastEthernet/IEEE 802.3 interfaces) and this router does not have any Ethernet interface so an error will occur when we enter the u201cinterface e0u201d

command.

New Questions 12

What occurs when an Ethernet cable is too long?

A. Giants

B. Runts

C. late collisions

D. interface resets

Answer: C

New Questions 13

Which adverse situation can occur if an Ethernet cable is too long?

A. late collisions

B. giants

C. interface resets

D. runts

Answer: A

New Questions 14

Refer to the exhibit. Which statement is correct regarding the results shown for the show interface s0/0/0 command?

A. The subnet mask for this interface is 255.255.255.248.

B. The subnet mask for this interface is 255.255.255.252.

C. The IP address that is configured on s0/0/0 is a public address.

D. This interface can be enabled by issuing a no shutdown command.

E. The default encapsulation protocol for a Cisco serial interface is PPP.

Answer: D

New Questions 15

Which option is a valid hostname for a switch?

A. Switch-Cisco

B. Switch-Cisco!

C. SwitchCisco

D. SwitchCisc0

Answer: D

Recommend!! Get the Approved 100-105 dumps in VCE and PDF From Dumpscollection, Welcome to download: http://www.dumpscollection.net/dumps/100-105/ (New 347 Q&As Version)