NEW QUESTION 1
A customer wants to decrease problem resolution time on their HPE infrastructure. Why would this customer benefit from Insight Remote Support?

• A. It provides event diagnosis and automatic, secure submission of hardware event notifications to HPE.
• B. It provides health monitoring and alerting and suggests resolutions for common issues.
• C. It monitors 1600 system parameters and applies analytics to predict problems before they can lead to system or component failure.
• D. It maintains an up-to-date change log by recording hardware and system changes in real-time.

Answer: A

NEW QUESTION 2
Exhibit:

Which HPE ProLiant Server meets the customer's requirements?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: B

NEW QUESTION 3
Why is RAID 6 the best option for a large RAID set for archive storage on large-capacity drives?

• A. to reduce risk during volume rebuild
• B. to increase write performance on the volume
• C. to maximize capacity of the volume
• D. to reduce drive wear

Answer: A

NEW QUESTION 4
A customer needs to implement VMware across a few racks of servers. They anticipate a large amount of VM creation and retirement.
What are key technologies in a Top of Rack (ToR) switch that support this environment? (Choose three.)

• A. Smart Rate Support
• B. Deep Packet Buffers
• C. VPN Support
• D. PoE support
• E. MLAG support
• F. Rapid Configuration Management

Answer: ABE

NEW QUESTION 5
You are working on a server, and you notice that the blue UID light on the server is flashing slowly. What does this indicate?

• A. The host server is in standby mode
• B. The system is being managed remotely
• C. The host has rebooted and is performing POST actions
• D. The system is experiencing power issues

Answer: B

NEW QUESTION 6
You are configuring a FlexFabric switch for a customer environment. The customer has requested specific SFP+ transceivers, power options, and cables.
Which HPE tool enables you to select and configure a switch according to precise specifications?

• A. Single Point of Connectivity Knowledge (SPOCK)
• B. Networking Online Configurator
• C. One Config Simple (OCS)
• D. Switch Selector

Answer: C

NEW QUESTION 7
You are installing an HPE ProLiant server in a rack at a customer site. The customer’s facility is in a high-voltage utility service area, and they want to be certain that the power supply is supported.
Which ProLiant feature addresses the customer’s concern?

• A. ProLiant servers can be configured for 380 – 400V AC in low-line and high-line utility service areas.
• B. ProLiant servers support 240 V DC power supplies because components in a direct current line are less prone to failure.
• C. Rack-mountable HPE servers ship with 110 V DC power supplies because direct current is less expensive for a low-line utility service over short distances.
• D. ProLiant servers include auto-sensing power supplies with a power input range of 100-240 VAC, so they can be used globally.

Answer: D

NEW QUESTION 8
You are troubleshooting an HPE Proliant ML350 Gen server. You determine that the active ROM is corrupt and the system has not automatically switched to the redundant ROM. You need to manually switch the ROM.
What should you do?

• A. Select the backup ROM in the BIOS.
• B. Reset the iLO controller
• C. Change the position of the system maintenance switch options.
• D. Move the system maintenance jumper to pins one and two.

Answer: C

NEW QUESTION 9
You are onsite at a customer location to install a new network switch. The customer wants users to be able to manage the switch through the IP network.
How should you connect the switch to the network?

• A. Configure multiple user IDs or roles for the console connection
• B. Configure the management IP address on the switch and enable Telnet or SSH access
• C. Use a dedicated console cable to create a dedicated management network for every user
• D. Connect the switch to the network by using the serial cable that ships with the switch

Answer: B

NEW QUESTION 10
Match the HPE Tool with its use case. Select all that apply.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:
One Config Advanced (OCA) - Estimate the power and cooling requirements and weight for a rack of equipment
Single Point of Connectivity Knowledge (SPOCK) - Check compatibility of storage components Products and solutions Now (PSNow) - Download a technical presentation for a DL380 Gen10

NEW QUESTION 11
A customer has an ESXi server in a branch office They need to perform backups locally. The local backups must be replicated to the main data center with built-in deduplication
What should the customer install at the branch office?

• A. StoreOnce 3100
• B. StoreOnce VSA
• C. MSA 2042
• D. Storevirtual VSA

Answer: D

NEW QUESTION 12
A company plans to purchase new HPE servers. The company needs to maximize local storage capacity within the servers.
Which HPE servers should the company install?

• A. ProLiant BL460c Gen10
• B. ProLiant DL380 Gen10
• C. ProLiant ML110 Gen 9
• D. ProLiant DL360 Gen 9

Answer: B

NEW QUESTION 13
A customer has implemented an HPE ProLiant server with internal storage and needs to monitor the array health status.
Which management application can the customer use to discover errors quickly and minimize the possible downtime?

• A. Insight Online
• B. Smart Storage Administrator
• C. Intelligent Management Center
• D. InfoSight

Answer: B

NEW QUESTION 14
You are installing a rack at customer site.
How can you ensure redundant power to the rack?

• A. Install two power distribution units (PDUs) with each one connected to a power socket supplied by an independent electrical power source.
• B. Ensure 3-phase power is available in the data center.
• C. Connect an uninterruptible power supply (UPS) to redundant circuit breakers at the facility power source.
• D. Use two different power cords to connect the server to the power grid at the customer site.

Answer: C

NEW QUESTION 15
A customer requires 12 Gb local storage for their VMware boot volumes, which require high-performance read cycles to enable the operating system to boot quickly.
Which drive type provides the most appropriate size and most cost-effective way to meet this requirement?

• A. Mixed-use SSD
• B. Flash media drive
• C. SATA nearline
• D. SAS midline

Answer: B

NEW QUESTION 16
You are managing a HPE ProLinat rack-mount server and need to determine when the Remote Console was most recently used.
Where can you find this information?

• A. System
• B. IML
• C. iLO
• D. Audit

Answer: C

NEW QUESTION 17
A customer needs to deploy an application on a newly-installed HPE ProLiant server, but they report that the server is not online. They call you for remote support. The IP address on the production network cannot be reached. You are evaluating the probable root causes of this issue.
According to the troubleshooting methodology, what are next two steps? (Select two)

• A. Remote console into the ToR switch to check the server's port configuration.
• B. Log in to iLO to see if the server hardware and NIC are online and configured correctly.
• C. Use OneView to see f the server firmware is up-to-date
• D. Run insight Diagnostics on the Server
• E. Use Microsoft Remote Desktop or VNC to check the server's NIC and IP address configuration

Answer: BD

NEW QUESTION 18
What should you install with a server for a customer who may need to perform maintenance on the server while it is the rack? (Select two.)

• A. Cable Management Arm (CMA)
• B. redundant PDUs
• C. high performance fan kit
• D. rack stabilization kit
• E. blanking panels

Answer: AD

NEW QUESTION 19
A customer is enhancing their server and storage virtualization infrastructure. They need to maximize memory density per rack unit and provide an all-flash array to the environment.
Which HPE solutions should they install to fulfill these requirements (Select two.)

• A. Nimble AF3000
• B. ProLiant ML350 Gen10
• C. ProLiant ML360 Gen10
• D. ProLiant ML380 Gen10
• E. MSA 2042

Answer: BE

NEW QUESTION 20
You are designing a network for a customer that needs a centrally-managed solution for their physical and virtual switches. This product must integrate with their existing third-party networking equipment.
Which HPE management solution meets the customer’s needs?

• A. Centralized Management Console
• B. Intelligent Resilient Framework
• C. Intelligent Management Center
• D. InfoSight

Answer: C

NEW QUESTION 21
A customer needs a Fibre Channel storage solution that supports block storage with the lowest cost. Which HPE solution meets this customer’s requirements?

• A. HPE Nimble Storage
• B. HPE SimpliVity
• C. HPE MSA
• D. HPE StoreVirtual VSA

Answer: C

NEW QUESTION 22
Match the feature to the lowest iLO5 license in which it is available

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:
Last - last 3-2
1-1
3-3

NEW QUESTION 23
......